en
My Requests
Following
I'D LIKE TO CHAT WITH A REPRESENTATIVE
I'D LIKE TO SUBMIT A SUPPORT REQUEST
Submit a Request
Contact Us
Is your question unavailable?
Chat with a Representative
Submit a Request
Attachments:

Logo

ZyXel VSG1432: Modem Setup (ADSL)

The ZyXel VSG1432 Modem can be setup in Routed or Bridge mode.

Routed mode is recommended for most users as it allows you to take full advantage of all of the ZyXel VSG1432's capabilities.

Bridge mode is only recommended for advanced users who intend to use their own stand-alone router/networking equipment.

Routed Mode

  1. Navigate to the modem's web interface. (192.168.1.1)
  2. Log in using the default username and password. (admin/1234)
  3. Hover over the Network Settings tab. (bottom center of screen)
  4. Click on the Broadband link.
  5. If an interface is already present in the table, click the trash can icon to delete it.
  6. Click the Add New WAN Interface button.
  7. Check the Active check box.
  8. Set the Name to whatever you would like. (or TekSavvy if you can't think up a name)
  9. Set the Type to ADSL over ATM.
  10. Set the Mode to Routing.
  11. Set the Encapsulation to PPPoE.
  12. Set the VPI and VCI fields to the correct VPI and VCI for your area.
    • Ontario/Quebec: 0/35
    • Alberta/BC: 0/33
    • Nova Scotia: 0/35 or 1/0
    • Nefoundland: 0/34, 0/35, 0/36, or 8/36
    • PEI: 0/35
    • New Brunswick: 0/34 or 0/35
  13. Set the Encapsulation Mode to LLC/SNAP-BRIDGING.
  14. Set the Service Category to UBR Without PCR.
  15. Enter your DSL user name into the PPP User Name field.
  16. Enter your DSL password into the PPP Password field.
  17. Check the PPP Auto Connect check box.
  18. Set the PPPoE Service Name to whatever you would like. (or TekSavvy)
  19. Set IP Address to Obtain an IP Address Automatically.
  20. Check the NAT Enable check box.
  21. Check the IGMP Proxy Enable check box.
  22. Check the Apply as Default Gateway check box.
  23. Set DNS to Dynamic.
  24. Click Apply.

Bridge Mode

  1. Navigate to the modem's web interface. (192.168.1.1)
  2. Log in using the default username and password. (admin/1234)
  3. Hover over the Network Settings tab. (bottom center of screen)
  4. Click on the Broadband link.
  5. If an interface is already present in the table, click the trash can icon to delete it.
  6. Click the Add New WAN Interface button.
  7. Check the Active check box.
  8. Set the Name to whatever you would like. (or TekSavvy if you can't think up a name)
  9. Set the Type to ADSL over ATM.
  10. Set the Mode to Bridge.
  11. Set the Encapsulation to PPPoE.
  12. Set the VPI and VCI fields to the correct VPI and VCI for your area.
    • Ontario/Quebec: 0/35
    • Alberta/BC: 0/33
    • Nova Scotia: 0/35 or 1/0
    • Nefoundland: 0/34, 0/35, 0/36, or 8/36
    • PEI: 0/35
    • New Brunswick: 0/34 or 0/35
  13. Set the Encapsulation Mode to LLC/SNAP-BRIDGING.
  14. Set the Service Category to UBR Without PCR.
  15. Click Apply.
Have more questions? Submit a request
Powered by Zendesk